A1601 settings - Revision history

Telcredstaff at 10:37, 26 January 2024

2024-01-26T10:37:17Z

← Older revision		Revision as of 10:37, 26 January 2024
Line 3:		Line 3:
	==== With direct doors only ====		==== With direct doors only ====

	The ~~A1001~~ controller can control one or two doors directly, meaning that the locks, monitors, and REX devices are connected to the physical connections on the controller.		The A1601 controller can control one or two doors directly, meaning that the locks, monitors, and REX devices are connected to the physical connections on the controller.

Telcredstaff: /* Pin chart */

2021-10-13T17:10:17Z

Pin chart

← Older revision		Revision as of 17:10, 13 October 2021
Line 111:		Line 111:


	[[File:A1601_pin_chart_link.png\|Pin chart link]]		[[File:A1601_pin_chart_link.png\|border\|Pin chart link]]

Telcredstaff: /* Pin chart */

2021-10-13T17:07:49Z

Pin chart

← Older revision		Revision as of 17:07, 13 October 2021
Line 108:		Line 108:
	=== Pin chart ===		=== Pin chart ===

	After saving or editing the settings for an A1601 controller, Telcred Access Manager can generate a pin chart that summarizes the physical connections on the controller. The pin chart is accessed by clicking the link in the ~~lower right hand corner~~ of the controller detail screen:		After saving or editing the settings for an A1601 controller, Telcred Access Manager can generate a pin chart that summarizes the physical connections on the controller. The pin chart is accessed by clicking the link at the bottom of the controller detail screen:

Telcredstaff: /* Door(s) */

2020-10-06T14:21:00Z

Door(s)

← Older revision		Revision as of 14:21, 6 October 2020
Line 1:		Line 1:
	=== Door(s) ===		=== Door(s) ===

			==== With direct doors only ====
	The A1601 controller can control one or two doors directly or:

	* one door directly and up to 8 Assa Aperio doors via a hub
			The A1001 controller can control one or two doors directly, meaning that the locks, monitors, and REX devices are connected to the physical connections on the controller.
	* one door directly and up to 16 SimonsVoss SmartIntego doors via a hub


Line 9:		Line 9:


	Select the first door from the dropdown list (you may need to create it first). If a ~~hub~~ should be ~~used~~ ~~with~~ ~~the~~ controller, it is ~~only~~ ~~available~~ ~~under the first~~ dropdown list ~~so select it here~~.		Select the first door from the dropdown list (you may need to create it first). If a second door should be controlled by this controller, select it from the second (optional) dropdown list.

			==== With SimonsVoss SmartIntego ====

			In combination with wireless locks from [[SimonsVoss SmartIntego]], each controller can still manage one or two doors directly. In addition, a controller can manage up to 30 (recommended max value) wireless locks via one or more IP-connected hubs. One SmartIntego hub can manage maximum 16 doors and has a range of 20 - 30 meters.

			The connection between the SmartIntego hub and the controller is done on the [[Hubs\|hub]] page.

			==== With Assa Aperio ====

			The [[Assa Aperio]] hub is connected physically to the reader socket on the A1001 and one controller can only manage one Assa Aperio hub. Hubs are available under the first dropdown list so select it here. Up to 8 Assa Aperio wireless locks can be managed by the hub.

	If a ~~second~~ ~~door~~ ~~should~~ be ~~controlled~~ by ~~this~~ ~~controller,~~ or if the controller ~~should~~ manage one ~~hub~~ ~~and~~ ~~one~~ ~~door~~ ~~directly~~, select it ~~from~~ the second (optional) dropdown list.		In addition to the Assa Aperio hub, it is possible to let the controller manage one door directly. In this case, select it in the second (optional) dropdown list.

	=== Lock settings ===		=== Lock settings ===

Telcredstaff: /* IO port settings */

2019-12-18T13:31:28Z

IO port settings

← Older revision		Revision as of 13:31, 18 December 2019
Line 91:		Line 91:


	[[File:~~ioport_settings~~.png\|IO port settings]]		[[File:ioport-settings-a1601.png\|A1601 IO port settings]]

Telcredstaff: /* IO port settings */

2019-12-18T13:25:46Z

IO port settings

← Older revision		Revision as of 13:25, 18 December 2019
Line 88:		Line 88:
	=== IO port settings ===		=== IO port settings ===

	The A1601 Network door controller has ~~SIX~~ configurable IO ports. These ports can be used with [[Commands and triggers]]; an input port can act as a trigger, and a command can activate an output port. In order to use the IO ports, they first need to be configured.		The A1601 Network door controller has six configurable IO ports. These ports can be used with [[Commands and triggers]]; an input port can act as a trigger, and a command can activate an output port. In order to use the IO ports, they first need to be configured.


Line 95:		Line 95:

	Each IO port can be configured either as ''input'' or ''output''. It is also necessary to define what the normal state of the port is: ''ground'' or ''open''. For more information on the use of IO ports, see the section on [[Commands and triggers]].		Each IO port can be configured either as ''input'' or ''output''. It is also necessary to define what the normal state of the port is: ''ground'' or ''open''. For more information on the use of IO ports, see the section on [[Commands and triggers]].


	=== Pin chart ===		=== Pin chart ===

Telcredstaff at 13:20, 18 December 2019

2019-12-18T13:20:02Z

← Older revision		Revision as of 13:20, 18 December 2019
Line 85:		Line 85:

	A special case of using a REX device / input is where a user opens the door manually and the door has a door monitor. Normally, this will trigger the ''door forced open'' alert, but this may not be the desired behavior. In this case, it is possible to use a specific REX device that will trigger as soon as the door starts to open and configure it as either ''Closing circuit allows'' or ''Opening circuit allows''. The effect of this is to prevent the ''door forced open'' alert to be generated.		A special case of using a REX device / input is where a user opens the door manually and the door has a door monitor. Normally, this will trigger the ''door forced open'' alert, but this may not be the desired behavior. In this case, it is possible to use a specific REX device that will trigger as soon as the door starts to open and configure it as either ''Closing circuit allows'' or ''Opening circuit allows''. The effect of this is to prevent the ''door forced open'' alert to be generated.

			=== IO port settings ===

			The A1601 Network door controller has SIX configurable IO ports. These ports can be used with [[Commands and triggers]]; an input port can act as a trigger, and a command can activate an output port. In order to use the IO ports, they first need to be configured.


			[[File:ioport_settings.png\|IO port settings]]


			Each IO port can be configured either as ''input'' or ''output''. It is also necessary to define what the normal state of the port is: ''ground'' or ''open''. For more information on the use of IO ports, see the section on [[Commands and triggers]].


	=== Pin chart ===		=== Pin chart ===

Telcredstaff: /* Lock settings */

2019-07-05T13:41:08Z

Lock settings

← Older revision		Revision as of 13:41, 5 July 2019
Line 36:		Line 36:
	* ''Fail-safe'' means that the door is unlocked if the power fails (it is safe for people on the inside, e.g. in the event of a fire).		* ''Fail-safe'' means that the door is unlocked if the power fails (it is safe for people on the inside, e.g. in the event of a fire).

	NOTE: In order for fail-secure and fail-safe to work as intended it is important to connect the wires from the lock to the relay in the correct way. Minus (-) from the lock should be connected to ~~GND~~ on the controller and plus (+) from the lock should be connected to NO on the controller.		NOTE: In order for fail-secure and fail-safe to work as intended it is important to connect the wires from the lock to the relay in the correct way. Minus (-) from the lock should be connected to minus (-) on the controller and plus (+) from the lock should be connected to NO on the controller.

	=== Monitor settings ===		=== Monitor settings ===

Telcredstaff: /* Lock settings */

2019-07-05T13:38:08Z

Lock settings

← Older revision		Revision as of 13:38, 5 July 2019
Line 35:		Line 35:
	* ''Fail-secure'' means that the door is locked if the power fails (it is secure from intruders on the outside). This is the default.		* ''Fail-secure'' means that the door is locked if the power fails (it is secure from intruders on the outside). This is the default.
	* ''Fail-safe'' means that the door is unlocked if the power fails (it is safe for people on the inside, e.g. in the event of a fire).		* ''Fail-safe'' means that the door is unlocked if the power fails (it is safe for people on the inside, e.g. in the event of a fire).

			NOTE: In order for fail-secure and fail-safe to work as intended it is important to connect the wires from the lock to the relay in the correct way. Minus (-) from the lock should be connected to GND on the controller and plus (+) from the lock should be connected to NO on the controller.

	=== Monitor settings ===		=== Monitor settings ===

Telcredstaff: /* Pin chart */

2019-07-05T07:56:05Z

Pin chart

← Older revision		Revision as of 07:56, 5 July 2019
Line 92:		Line 92:


	[[File:~~pin_chart~~.png\|Pin chart]]		[[File:A1601_pin_chart.png\|Pin chart]]